Default Configuration

-When first using the mod or after a master reset the reflex buttons on the controller will function individually as one of the 4 action buttons (Triangle, Circle, Square and X). The button locations can vary depending on installation and qty of buttons installed. However using the programming mode below you can change the reflex button assignment to be any controller button you like. 

(Reflex button mean rear button)

Programming Mode

-To enter the programming mode, HOLD R1, R2, L1, and L2 at the same time for ~8 seconds. There is a small LED in the touchpad lightbar that will flash red.

-An alternate way to enter programming mode is to HOLD DPad Down, X, and Square for ~ 8 seconds. The small LED in the touchpad lightbar that will flash red.

-To configure a reflex button for standard button remapping, press and hold a reflex button, while holding tap any button you would like to assign.

-Example: Hold reflex button, tap triangle, release reflex button. When the reflex button is pressed, Triangle will be pressed on the controller.

Disable Button

-To disable a button, after entering the programming mode press the rear reflex button you’d like to disable and the LED will flash. Repeat for however many buttons you would like to disable. Tap the touchpad to exit the programming mod and the button should be disabled. To re-enable it, just program it to a button again.

Exit Mode

-To exit the programming mode and save your configuration just tap the touchpad and the small LED should flash again.

Master Reset

-To reset the mod to default settings, turn off the controller hold X + Triangle + Circle + Square and turn on the controller. You will see the LED flash very fast 10 times

Default Configuration

-When first using the mod or after a master reset the reflex buttons on the controller will function individually as one of the 4 action buttons (Triangle, Circle, Square and X). The button locations can vary depending on installation and qty of buttons installed. However using the programming mode below you can change the reflex button assignment to be any controller button you like. 

(Reflex button means rear button)

Programming Mode

-To enter the programming mode, HOLD R1, R2, L1, and L2 at the same time for ~8 seconds. The mute button will flash red.

-An alternate way to enter programming mode is to HOLD DPad Down, X, and Square for ~ 8 seconds. The mute button will flash red.

-To configure a reflex button for standard button remapping, press and hold a reflex button, while holding tap any button you would like to assign.

-Example: Hold reflex button, tap triangle, release reflex button. When the reflex button is pressed, Triangle will be pressed on the controller. 

Disable Button

-To disable a button, after entering the programming mode press the rear reflex button you’d like to disable and the mute button will flash. Repeat for however many buttons you would like to disable. Press UP on the dpad and the button should be disabled. To re-enable it, just program it to a button again.

Exit Mode

-To exit the programming mode and save your configuration just tap UP on the D-pad. 

Master Reset

-To reset the mod to default settings, turn off the controller hold X + Triangle + Circle + Square and turn on the controller. You will see the LED flash very fast 10 times

Default Configuration

-When first using the mod or after a master reset the reflex buttons on the controller will function individually as one of the 4 action buttons (A, B, X, and Y). The button locations can vary depending on installation and qty of buttons installed. However using the programming mode below you can change the reflex button assignment to be any controller button you like. 

(Reflex buttons means rear button)

Programming Mode

-To enter the programming mode, HOLD RT, RB, LT, LB at the same time for ~8 seconds. The Xbox home button will flash.

-To configure a reflex button for standard button remapping, press and hold a reflex button, while holding tap any button you would like to assign.

-Example: Hold reflex button, tap Y, release reflex button. When the reflex button is pressed, Y will be pressed on the controller.

Disable Button

-To disable a button, after entering the programming mode press the rear reflex button you’d like to disable and the Xbox home will flash. Repeat for however many buttons you would like to disable. Press the view button and the button should be disabled. To re-enable it, just program it to a button again.

Exit Mode

-To exit the programming mode and save your configuration just tap the view button. 

Master Reset

-To reset the mod to default settings, turn off the controller hold A + B + X + Y and turn on the controller. You will see the Xbox home button flash very fast 10 times